| ︙ | | |
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
|
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
|
-
+
|
(set-run-config-vars run-id keyvals target) ;; (db:get-target db run-id))
;; environment overrides are done *before* the remaining critical envars.
(alist->env-vars env-ovrd)
(set-megatest-env-vars run-id)
(set-item-env-vars itemdat)
(save-environment-as-files "megatest")
;; open-run-close not needed for test-set-meta-info
(tests:set-meta-info #f test-id run-id test-name itemdat 0 work-area)
(tests:set-full-meta-info #f test-id run-id 0 work-area)
(tests:test-set-status! test-id "REMOTEHOSTSTART" "n/a" (args:get-arg "-m") #f)
(if (args:get-arg "-xterm")
(set! fullrunscript "xterm")
(if (and fullrunscript (not (file-execute-access? fullrunscript)))
(system (conc "chmod ug+x " fullrunscript))))
;; We are about to actually kick off the test
;; so this is a good place to remove the records for
|
| ︙ | | |
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
|
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
|
-
+
|
(vector-set! exit-info 0 pid)
(vector-set! exit-info 1 exit-status)
(vector-set! exit-info 2 exit-code)
(set! rollup-status exit-code)
(mutex-unlock! m)
(if (eq? pid-val 0)
(begin
(thread-sleep! 2)
(thread-sleep! 1)
(loop (+ i 1)))
)))))
;; then, if runscript ran ok (or did not get called)
;; do all the ezsteps (if any)
(if ezsteps
(let* ((testconfig (read-config (conc work-area "/testconfig") #f #t environ-patt: "pre-launch-env-vars")) ;; FIXME??? is allow-system ok here?
(ezstepslst (hash-table-ref/default testconfig "ezsteps" '())))
|
| ︙ | | |
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
|
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
|
-
+
|
(mutex-lock! m)
(vector-set! exit-info 0 pid)
(vector-set! exit-info 1 exit-status)
(vector-set! exit-info 2 exit-code)
(mutex-unlock! m)
(if (eq? pid-val 0)
(begin
(thread-sleep! 2)
(thread-sleep! 1)
(processloop (+ i 1))))
))
(let ((exinfo (vector-ref exit-info 2))
(logfna (if logpro-used (conc stepname ".html") "")))
;; testing if procedures called in a remote call cause problems (ans: no or so I suspect)
(db:teststep-set-status! #f test-id stepname "end" exinfo #f logfna work-area: work-area))
(if logpro-used
|
| ︙ | | |
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
|
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
|
+
-
+
|
(calc-minutes (lambda ()
(inexact->exact
(round
(-
(current-seconds)
start-seconds)))))
(kill-tries 0))
(tests:set-full-meta-info #f test-id run-id (calc-minutes) work-area)
(let loop ((minutes (calc-minutes)))
(begin
(set! kill-job? (or (test-get-kill-request test-id) ;; run-id test-name itemdat))
(and runtlim (let* ((run-seconds (- (current-seconds) start-seconds))
(time-exceeded (> run-seconds runtlim)))
(if time-exceeded
(begin
(debug:print-info 0 "KILLING TEST DUE TO TIME LIMIT EXCEEDED! Runtime=" run-seconds " seconds, limit=" runtlim)
#t)
#f)))))
;; open-run-close not needed for test-set-meta-info
(tests:set-meta-info #f test-id run-id test-name itemdat minutes work-area)
(tests:set-partial-meta-info #f test-id run-id minutes work-area)
(if kill-job?
(begin
(mutex-lock! m)
;; NOTE: The pid can change as different steps are run. Do we need handshaking between this
;; section and the runit section? Or add a loop that tries three times with a 1/4 second
;; between tries?
(let* ((pid (vector-ref exit-info 0)))
|
| ︙ | | |